Every hydraulic thread in the world can be narrowed to one family and one size in four measurements. Take them in this order — taper, pitch, angle, then the sealing seat. Doing it in a different order is why people order the wrong fitting.
Look at the male thread. If it forms a cone, getting narrower at the tip, it is a pipe thread that seals on the threads themselves and needs sealant. If the threads are parallel like a bolt, it is a modern fitting — the threads only clamp, and the seal happens somewhere else.
Tapered: NPT, BSPT · Parallel: JIC, SAE ORFS, BSPP, Metric, SAE ORB
Use a pitch gauge, not a ruler. Inch threads are counted in threads per inch (TPI); metric and British threads are measured as pitch in millimetres. Pitch is how you separate an NPT from a JIC of the same diameter — they look alike at the caliper and differ here.
55° means Whitworth — that is BSP, both parallel and tapered. 60° means everything else: NPT, JIC, SAE ORFS, Metric. This single number eliminates half the chart.
60° flank angle, 1:16 taper, seals on the threads. Requires sealant or PTFE tape. The nominal size is not the measured diameter — check the chart.
| Nominal | Thread callout | TPI | OD at thread end (mm) | Taper |
|---|---|---|---|---|
| 1/8 | 1/8-27 | 27 | 10.24 | 1:16 |
| 1/4 | 1/4-18 | 18 | 13.72 | 1:16 |
| 3/8 | 3/8-18 | 18 | 17.15 | 1:16 |
| 1/2 | 1/2-14 | 14 | 21.34 | 1:16 |
| 3/4 | 3/4-14 | 14 | 26.67 | 1:16 |
| 1 | 1-11.5 | 11.5 | 33.40 | 1:16 |
| 1-1/4 | 1-1/4-11.5 | 11.5 | 42.16 | 1:16 |
| 1-1/2 | 1-1/2-11.5 | 11.5 | 48.26 | 1:16 |
| 2 | 2-11.5 | 11.5 | 60.33 | 1:16 |
55° flank angle, parallel. Seals on an O-ring, a bonded washer or a metal-to-metal shoulder — never on the threads. Standard across Europe and much of Asia.
| Nominal | Thread callout | TPI | OD (mm) |
|---|---|---|---|
| 1/8 | G 1/8 | 28 | 9.73 |
| 1/4 | G 1/4 | 19 | 13.16 |
| 3/8 | G 3/8 | 19 | 16.66 |
| 1/2 | G 1/2 | 14 | 20.96 |
| 3/4 | G 3/4 | 14 | 26.44 |
| 1 | G 1 | 11 | 33.25 |
| 1-1/4 | G 1-1/4 | 11 | 41.91 |
| 1-1/2 | G 1-1/2 | 11 | 47.80 |
| 2 | G 2 | 11 | 59.61 |
55° flank angle, 1:16 taper, seals on the threads. Same nominal diameters as BSPP but not interchangeable — the angle differs from NPT and the pitch differs from both.
60° flank angle, parallel threads, 37° flare seat. Dash size refers to the tube, not the thread — a -08 tube can carry different thread sizes depending on fitting type. Measure the thread, not the dash number.
| Dash | Thread callout | Tube OD | TPI | Thread OD (mm) |
|---|---|---|---|---|
| -04 | 7/16-20 | 7/16" | 20 | 11.11 |
| -05 | 1/2-20 | 1/2" | 20 | 12.70 |
| -06 | 9/16-18 | 9/16" | 18 | 14.29 |
| -08 | 3/4-16 | 3/4" | 16 | 19.05 |
| -10 | 7/8-14 | 7/8" | 14 | 22.23 |
| -12 | 1-1/16-12 | 1-1/16" | 12 | 26.99 |
| -14 | 1-3/16-12 | 1-3/16" | 12 | 30.16 |
| -16 | 1-5/16-12 | 1-5/16" | 12 | 33.34 |
| -20 | 1-5/8-12 | 1-5/8" | 12 | 41.28 |
| -24 | 1-7/8-12 | 1-7/8" | 12 | 47.63 |
60° flank angle, parallel threads, flat face with an O-ring groove. Common on mobile equipment and anywhere a JIC flare would weep under vibration.
| Dash | Thread callout | TPI | Thread OD (mm) |
|---|---|---|---|
| -04 | 9/16-18 | 18 | 14.29 |
| -06 | 11/16-16 | 16 | 17.46 |
| -08 | 13/16-16 | 16 | 20.64 |
| -10 | 1-14 | 14 | 25.40 |
| -12 | 1-3/16-12 | 12 | 30.16 |
| -16 | 1-7/16-12 | 12 | 36.51 |
| -20 | 1-11/16-12 | 12 | 42.86 |
| -24 | 2-12 | 12 | 50.80 |
60° flank angle, 24° cone with a cutting ring (light and heavy series). Standard on German and much of European machinery.
| Thread | Pitch (mm) | Nominal OD (mm) | Series |
|---|---|---|---|
| M12 × 1.5 | 1.5 | 12.00 | Light series |
| M14 × 1.5 | 1.5 | 14.00 | Light series |
| M16 × 1.5 | 1.5 | 16.00 | Light series |
| M18 × 1.5 | 1.5 | 18.00 | Light series |
| M22 × 1.5 | 1.5 | 22.00 | Light series |
| M26 × 1.5 | 1.5 | 26.00 | Light series |
| M30 × 2.0 | 2.0 | 30.00 | Heavy series |
| M36 × 2.0 | 2.0 | 36.00 | Heavy series |
| M42 × 2.0 | 2.0 | 42.00 | Heavy series |
| M52 × 2.0 | 2.0 | 52.00 | Heavy series |
These are the pairs that get ordered wrong most often. In each case the parts look identical in a photograph and differ by a few tenths of a millimetre.
| Trap | Why it catches people | How to tell |
|---|---|---|
| 1/2” NPT vs 1/2” BSPP | 21.34 mm vs 20.96 mm — 0.38 mm apart. Both are “1/2 inch” and both are common. | Thread pitch gauge: NPT is 14 TPI at 60°, BSPP is 14 TPI at 55°. Same pitch, different angle. A BSPP nut will start on an NPT thread and then leak. |
| JIC vs SAE ORFS, same dash | Both 60° with parallel threads. Dash -08 is 3/4-16 on JIC but 13/16-16 on ORFS. | Look at the seat: 37° cone is JIC, flat face with O-ring groove is ORFS. Then confirm the thread OD. |
| BSPP vs BSPT, same nominal | Same diameter, same 55° angle, same nominal callout. | Measure the diameter at the front and at the back of the thread. Equal = BSPP. Decreasing = BSPT. |
| Dash size vs thread size | A -08 tells you the tube is 1/2”. It does not tell you the thread. | Always measure the thread OD. Never order on the dash number alone. |
Three instruments cover every case on this page: a digital caliper for diameter, a thread pitch gauge with both TPI and metric leaves, and a seat angle gauge. A thread identification kit puts all three in one case.
The seat gauge carries four detents, and each one maps to a specific seat form — note that the gauge reads the half angle from the centreline, so a 12° blade identifies a 24° cone:
| Detent | Seat form | Where you meet it |
|---|---|---|
| 12° | DIN 24° cone (ISO 8434-1 / DIN 2353) | European metric tube fittings. Straight metric thread with an O-ring or metal-to-metal seal. |
| 30° | JIS / Komatsu 30° flare | Japanese and Korean equipment. Straight thread — BSPP for JIS, metric for Komatsu. A 30° flare nose, not JIC 37°. |
| 37° | JIC 37° flare (SAE J514) | North American hydraulic standard. Straight UN/UNF thread, metal-to-metal seal. Looks like a 45° flare but seals only at 37°. |
| 45° | SAE 45° flare (SAE J512) | Automotive, refrigeration and lighter-duty hydraulics. Same UN/UNF threads as JIC, wider flare angle. |
If you have the three measurements but not the chart, our free tool names the thread from those numbers and flags the look-alike sizes: Thread ID Mate. It works offline once installed, and needs no signup.
Reference data only. Verify against current standards (SAE J514, ISO 7-1, ISO 228-1, ANSI/ASME B1.20.1, DIN 2353) and confirm with a calibrated gauge before ordering or assembling. Working on pressurised hydraulic systems carries serious injury risk — isolate and relieve pressure before loosening any fitting.
Send the thread callout, the material and the quantity. You get a price, a 35-day lead time, and the factory we would use for that item.